Shaped charge penetration into high- and ultrahigh-strength Steel–Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete (RPC) targets were performed in this paper. Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete (NSC). The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge. The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC. The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RPC target are discussed. Moreover, a theoretical model is presented to describe the penetration of shaped charge into RPC target. As the concrete strength increases, the penetration resistance increases and the entrance crater diameter decreases. Given the drift velocity and narrow crater channel, the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth. Moreover, the narrow channel has a stronger interference to the jet particles with increasing concrete strength; hence, the gap effects must be considered. The drift velocity and gap effects, which are the same as penetration resistance, also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete. The crater profiles are calculated through a theoretical model, and the results are in good agreement with the experiments.     

华东烧结模型的数学计算(Ⅲ)

通过热力学分析和计算,讨论等径球(椭球)与均匀分布不等径球(椭球)的体心正方堆积的烧结体积和表面能的变化,包括华东烧结模型中膨胀机制和收缩机制,对烧结体总表面能变化的作用和影响,发现随着烧结过程的进行,烧结收缩机制逐渐占主导地位。     

火工品装药计量板模糊控制器的设计

通过对火工品装药计量板的模型分析 ,利用模糊控制技术实现对装药计量板的自动控制。采用近似推理方法的ARMCE简化算法实现了模糊控制器的设计 ,并进行了模拟仿真验证。结果表明该控制方案对解决火工品装药计量板的自动控制这一“瓶颈”问题是有效的。     

电子设备房自动灭火系统研究

针对计算机房及电子设备房的火灾进行了分析,就计算机房及电子设备房的环境条件进行对比,对目前较广泛采用的几种自动灭火系统装置及其灭火剂的性能、环保等几个方面,进行了阐述和比较,希望对消防部队的日常监督检查提供参考依据。     

聚铝碳硅烷的流变性和纺丝性研究

采用单孔纺丝装置对不同铝含量的聚铝碳硅烷(PACS)的流变性和流变性进行研究.结果表明:随着温度升高,PACS熔体的流体特性逐渐接近牛顿流体;PACS熔体粘度对温度有强烈的依赖性,其软化点在190℃～220℃范围时,其粘流活化能在190～260kJ/mol之间;当PACS的粘度在100Pa·s左右时可纺性好;铝含量对PACS的流变性能和可纺性有重要的影响,随着铝含量的增加,PACS熔体的粘度增大,因而PACS的纺丝温度更高,可纺性变差.     

C/SiC复合材料残余应力的电火花小孔法测定研究

进行了C/SiC复合材料残余应力的小孔法表征.基于现有小孔法的不足以及材料的较好电导率,提出了电火花打孔法的残余应力测量方法,建立了相应的残余应力测量流程.进行了不同平整表面样品的残余应力测量.结果表明电火花打孔法具有较好的区分性,也表明C/SiC复合材料具有较小的本征残余应力和机加工应力,这说明:C/SiC复合材料作为反射镜材料具有很好的面形稳定性的优势.     

超音速等离子制备Al/Ni涂层的性能特点

以超音速等离子喷涂系统(HEPJet)为平台,采用铝包镍(Al/Ni)自粘结粉末,借助Spray Watch2i在线监测系统、扫描电子显微镜(SEM)、X射线衍射仪(XRD)和WE-10A万能拉伸试验机,研究了超音速等离子喷涂Al/Ni粒子的速度、温度及涂层的组织性能。研究结果表明:超音速等离子喷涂Al/Ni自粘结粉末时,与普通火焰喷涂不同,射流中无明显的放热反应特征,涂层中也未发现Al-Ni化合物;超音速等离子的喷涂功率、喷涂距离等参数对Al/Ni喷涂粒子的状态和涂层组织性能影响显著,当功率为54.6kW、喷涂距离为150mm时,Al/Ni涂层组织致密,与基体的结合强度高达56MPa。